Skip to main content

Scavenge fire

What is scavenge fire ?

Carbonized lube oil, unburnt fuel oil and carbon from the residual products of the combustion spaces are accumulated in the scavenge spaces with the running of the engine. Under certain faulty running condition of the engine, these may ignite causing a fire in the enclosed scavenge space, known as scavenge fire.

Causes of Scavenge Fire

  1. Blow past of combustion products caused by leaky, sticky or broken piston rings, worn out liner, faulty cylinder lubrication, or insufficient axial clearance of the piston rings.
  2. Overheated piston dissipates heat to the under piston area caused by faulty atomization and injection pressure, faulty fuel pump timing, loss of compression, engine overload, failure of coolant circulation or insufficient cooling due to formation of scale.
  3. Blow back of exhaust gases caused by exhaust back pressure or deposits on exhaust ports, fouling of grid before turbine inlet, fouling of turbine blades, choking of EGB or economiser gas outlet.
  4. Presence of fuel oil in the scavenge spaces due to defective fuel injectors, incorrect pressure setting of injectors or fuel particles landing on the cylinder liner due to excessive penetration.
  5. Excessive cylinder lubrication which is drained down to scavenge spaces.
  6. Oxygen is plenty during engine operation.
  7. Fouled scavenge manifold.

Indication of Scavenge Fire

  1. Engine revolution drops as the power generation in the affected cylinder is reduced.
  2. Unstable operation of Turbo charger and may cause surging.
  3. Exhaust temperature of the affected cylinder increases, as the cylinder is not receiving fresh air.
  4. Black smoke with exhaust due to incomplete combustion in that unit.
  5. Discharging of spark, flame or smokes through drain cocks from scavenge air boxes.
  6. Rise of pressure and temperature of air in the air box below the piston.
  7. Visible evidence of fire if a transparent window is fitted.
  8. Cooling water outlet temperature of the affected unit is increased.

Action to be Taken

  1. Inform bridge and reduce the speed.
  2. Cut of fuel supply to the affected unit and shut off valves.
  3. Cylinder lubrication is increased.
  4. Coolant flow through jacket and piston is maintained.
  5. Drains to be shut to prevent flow of spark in engine room.
  6. Keep clear of scavenge space relief valve to prevent human injury.
Fire should be extinguished after some time. If the fire spread in the other scavenge spaces along with the scavenge manifold, then –
  1. Inform bridge and stop the engine
  2. Stop fuel oil booster pump
  3. Open indicator cocks, engage turning gear and turn engine to prevent engine seizure
  4. Normal engine cooling and lubrication are maintained
  5. Scavenge air duct flap valve before engine is to be shut
  6. Release the smothering gases (Steam or CO2) to extinguish fire
  7. Before opening scavenge door ventilate the space thoroughly if CO2 is released.

Inspection after Scavenge Fire

  1. Intense fire can cause distortion and may upset piston alignment
  2. Check by turning the engine and watch movement of piston in the liner, check for any occurrence of binding  at part of stroke (Binding indicates misalignment of piston)
  3. Check spring on scavenge space relief device, if the device was near the set of fire
  4. Piston rod packing spring also should be checked, which may have become weakened by overheating
  5. Check piston rings and liner for any distortion or reddish burning mark
  6. Check diaphragm and frame near affected part
  7. Check guides and guide shoes
  8. Check tension of tie bolts

Prevention of Scavenge Fire

  1. Clean scavenge space and drain at regular intervals
  2. Keep scavenge space drain open at regular intervals
  3. Excess cylinder lubrication must be avoided
  4. In case of timed lubrication, the time has to be checked as per PMS
  5. Piston rings must be properly maintained and lubricated adequately
  6. Piston rod stuffing box must be maintained to prevent oil ingress in the scavenge space.
  7. Prolong engine or any cylinder over loading to be avoided
  8. Cylinder liner wear must be within admissible limits

Scavenge Space Protection Devices

  • Electrical temperature sensing device fitted within the trunking, which will automatically sound an alarm in the event of excessive rise in local temperature.
  • Pressure relief valves consisting of self closing spring loaded valves are fitted and should be examined and tested periodically.
  • Fixed fire extinguishing system may be CO2, Dry Powder or Steam.

Comments

  1. Enjoyed the article, really explains everything in detail, it is very interesting and useful at the same time. Keep up the good work. fire damage restoration drexel hill. Thank you.

    ReplyDelete
  2. The context of this content is really good. Thank you for sharing this type of awareness with us. In this article, you shared much informative knowledge on multiplication activities. Take look at this tooMold Solutions & Inspections . Thanks!

    ReplyDelete

Post a Comment

If you have any doubts.Please let me know

Popular posts from this blog

Differences between MC/MC-C and ME/ME-C engines

The electrohydraulic control mechanisms of the ME engine replace the following components of the conventional MC engine: Chain drive for camshaft Camshaft with fuel cams, exhaust cams and indicator cams Fuel pump actuating gear, including roller guides and reversing mechanism Conventional fuel pressure booster and VIT system Exhaust valve actuating gear and roller guides Engine driven starting air distributor Electronic governor with actuator Regulating shaft Engine side control console Mechanical cylinder lubricators. The Engine Control System of the ME engine comprises: Control units Hydraulic power supply unit Hydraulic cylinder units, including: Electronically controlled fuel injection, and Electronically controlled exhaust valve activation Electronically controlled starting air valves Electronically controlled auxiliary blowers Integrated electronic governor functions Tacho system Electronically controlled Alpha lubricators

Main engine interlocks

Interlocks are provided so that the engine can be started or reversed only when certain conditions have been fulfilled. When there is a remote control of engines, it is essential to have interlocks. This reduces the possibility of engine damage and any hazards to the operating personnel. Turning gear Interlock . This device prevents the engine from being started if the Turning gear is engaged. Running Direction Interlock . This prevents the fuel from being supplied if the running direction of the engine does not match the Telegraph. Starting Air Distributor in end position . This prevents starting from taking place if the shifting of the Distributor has not been completed. Main Lube. oil pressure, Piston cooling pressure, Jacket water pressure, and important parameters must be above the required minimum. Auxiliary Blower Interlock . The Auxiliary Blower is provided in case of Constant pressure turbo charging. Air Spring pressure Interlock . In case of the present generation

Why is a man hole door elliptical in shape?

Any opening in a pressure vessel is kept to a minimum and for a man entry an elliptical hole  is lesser in size than the corresponding circular hole. More over it is prime concern to have a  smoothed generous radius at the corners to eliminate stress concentration. Hence other  geometrical shapes like rectangle and square are ruled out.  To compensate for the loss of material in the shell due to opening, a doubler ring has to be  provided around the opening. The thickness of the ring depends on the axis length along the  dirrection in which the stresses are maximum and the thickness of the shell. It is important to  align the minor axis along the length of the vessel, as the stress in this direction is  maximum. Longitudinal stress: Pd/2t where P= pressure inside the vessel, d= diameter of the arc, t=  thickness of the shell plating  Circumferential stress: Pd/4t  More over a considerable material and weight saving is achieved as minor is along the  direction of maximum stress.