Like Aux engines which have a manual tappet to adjust , there must be a tappet clearance for the main engine as well. But with the absence of a rocker arm and spring – adjusting is not possible
In other words there is no real tappet for main engine
The exhaust valve is actuated hydraulically by oil from a hydraulic pump and is shut by spring air , when the spring air pressure exceeds the hydraulic oil pressure , This happens when the roller ( of the pump that is actuating the hydraulic valve ) is resting on the base circle of the cam
There is a valve called a throttle valve that is fitted on the hydraulic pump unit ( which actuated the opening of the exhaust valve)
When the system is just put into use the oil is relatively cold . After some time of operation the oil heats up and expands .This additional oil can make the exhaust valve stay open – leading to reduced Pcomp ,Pmax , reduced power and burning of the valve seat.
In order to prevent the valve being open due to the expansion of the hot oil , the throttle valve bleeds off a small quantity of oil each time it closes.
If the throttle valve bleeds off too much the valve can bounce shut, thus damaging it . This adjustment of the throttle valve bleeds off the quantity if called “ VIRTUAL TAPPET “
Correcting setting of the Virtual Tappet ensures positive closing of the valve in a smooth manner without bouncing.
THROTTLE VALVE: It is a needle valve , at bottom of the cylinder . This is compensation for leakages which can occur in system . It is usually set by builders and adjusted at a trials .Tightening the throttle screw reduces the leakage amount and vice versa.
If leakage is small . then the amount of pressure generated within the high pressure line will be more .This will cause the exhaust valve to open earlier and close later , then intended .To certain degree it will increase SFOC and thermal load on valve seats will also cause deterioration of the dead slow performance .To compensate for this the throttle valve will be opened and bleed oil from the system
If the leakage increases (If the total leakage amount coming from the throttle valve and hydraulic system exceeds a certain quantity ) the pressure in the high pressure line falls too quickly the valve will knock while closing .Pressure impact can also appear in hydraulic system when the valve is opening .This increase in the impact can increase seat indentation damage . In this case throttle valve should be closed to prevent this noise and damage
The optimum setting of throttle valve , is when the exhaust valve just begins to knock and then closed in further 30 degree adjustments should be made with engine at 75 % load plus . If the exhaust valve does not knock , with the fully open throttle valve , this means that hydraulic system is completely sealed ( no leaks at all) the throttle valve in this case should be turned to 150 degree open
In other words there is no real tappet for main engine
The exhaust valve is actuated hydraulically by oil from a hydraulic pump and is shut by spring air , when the spring air pressure exceeds the hydraulic oil pressure , This happens when the roller ( of the pump that is actuating the hydraulic valve ) is resting on the base circle of the cam
There is a valve called a throttle valve that is fitted on the hydraulic pump unit ( which actuated the opening of the exhaust valve)
When the system is just put into use the oil is relatively cold . After some time of operation the oil heats up and expands .This additional oil can make the exhaust valve stay open – leading to reduced Pcomp ,Pmax , reduced power and burning of the valve seat.
In order to prevent the valve being open due to the expansion of the hot oil , the throttle valve bleeds off a small quantity of oil each time it closes.
If the throttle valve bleeds off too much the valve can bounce shut, thus damaging it . This adjustment of the throttle valve bleeds off the quantity if called “ VIRTUAL TAPPET “
Correcting setting of the Virtual Tappet ensures positive closing of the valve in a smooth manner without bouncing.
THROTTLE VALVE: It is a needle valve , at bottom of the cylinder . This is compensation for leakages which can occur in system . It is usually set by builders and adjusted at a trials .Tightening the throttle screw reduces the leakage amount and vice versa.
If leakage is small . then the amount of pressure generated within the high pressure line will be more .This will cause the exhaust valve to open earlier and close later , then intended .To certain degree it will increase SFOC and thermal load on valve seats will also cause deterioration of the dead slow performance .To compensate for this the throttle valve will be opened and bleed oil from the system
If the leakage increases (If the total leakage amount coming from the throttle valve and hydraulic system exceeds a certain quantity ) the pressure in the high pressure line falls too quickly the valve will knock while closing .Pressure impact can also appear in hydraulic system when the valve is opening .This increase in the impact can increase seat indentation damage . In this case throttle valve should be closed to prevent this noise and damage
The optimum setting of throttle valve , is when the exhaust valve just begins to knock and then closed in further 30 degree adjustments should be made with engine at 75 % load plus . If the exhaust valve does not knock , with the fully open throttle valve , this means that hydraulic system is completely sealed ( no leaks at all) the throttle valve in this case should be turned to 150 degree open
I always check this type of advisory post and I found your article which is related to my interest. This is a great way to increase knowledge for us. Thanks for sharing an article like this.Hydraulic Crimping Tool
ReplyDeleteThroughout this post needle valves manufacturers in india, it provides me with some excellent information. The material you presented during this write-up was very useful. Keep posting.
ReplyDelete