Skip to main content

What is the routine maintenance, checks on the PV breaker?

CHECKS: 
a. Check the seal liquid periodically and replenish the liquid in case 
• Liquid levels of inner and outer pipes do not coincide 
• “0” points of inner and outer pipes do not coincide when the pressure inside 
the cargo tanks is atmospheric pressure 
b. Clean the flame screen in the cover at the top when the ships makes a dock-in 

CHECKING PROCEDURE: 
a. Checking the liquid level of the inner pipe (open the vent cock located at most top of 
the gauge, close the upper gauge cock and open the lower gauge cock) this is also 
termed as “bigger range” 
b. Checking the liquid level of the outer pipe (close the vent cock, open the upper gauge 
cock also open the lower gauge cock) this is also termed as “smaller range” 
Two distinct scales are provided for the liquid gauge one “higher” and other “lower” the 
respective readings (as in ‘a’ and ‘b’) should match numerically 

MAINTENANCE & INSPECTION IN DRYDOCK: 
Disconnect and remove top cover with attached internal stand pipe. Disconnect and remove 
Flame Arrestor Assembly. Remove flame screen. Thoroughly clean internal of flame arrestor. 
Renew flame screen with shipyard supplied equivalent type mesh. Drain breaker liquid, 
thoroughly clean internal breaker body, and stand pipe. Apply two coats of shipyard supplied  tar epoxy by hand brushing to all internal surfaces. Level gauges, cocks and protective  housing to be removed and transported to workshop for cleaning and overhaul. Dismantle  sight glass tubes and cocks for overhauling and cleaning. Upon completion, re-assemble and  re-install onboard with new shipyard supplied approved type jointings, studs, and nuts. 
Prove filling and level cocks clear and free. Disconnect and remove PV Breaker valve. 
Dismantle and clean surfaces. Lap valve and disc. Set valve to +0.21kg/cm2 and 
0.07kg/cm2 in the presence of the attending superintendent. Record and submit calibration 
of valve settings. Close on completion with new shipyard supplied approved type jointings 
and sealing compound and bolts and nuts.

Comments

  1. Great article by the great author, it is very massive and informative but still preaches the way to sounds like that it has some beautiful thoughts described so I really appreciate this article. Best Valve testing in UAE Services Provider

    ReplyDelete
  2. The liquid level of the inner and outer pipes is not the same, so it is not easy to check the seal liquid. You have mentioned some great points, but I think it would be better to seek the help of experts than to do this complicated task yourself. Dissertation Editing Service

    ReplyDelete
  3. After a long time, I read a very beautiful and very important article that I enjoyed reading. I have found that this article has many important points, I sincerely thank the admin of this website for sharing it. sight glass

    ReplyDelete
  4. Very Informative Blog. Thanks for sharing this. Looking for hire iPhone /iOS QA Developers, Programmers From India? We offers custom iPhone, iOS application development services Our developers are well-versed in creating apps for a range of industries including health, e-commerce, Cloud applications and luxury applications.안동출장아로마
    영천출장아로마
    영주출장아로마
    포항출장아로마
    경산출장아로마

    ReplyDelete
  5. What liquid we put in PV breaker? Is it possible to put only fresh water while you are in warm temperature?

    ReplyDelete
  6. I really appreciate how this article emphasizes the importance of documentation during routine maintenance checks. Keeping track of inspections, repairs, and any recurring issues seems like a crucial aspect of maintaining equipment. Dissertation Writing Services UK

    ReplyDelete

Post a Comment

If you have any doubts.Please let me know

Popular posts from this blog

Differences between MC/MC-C and ME/ME-C engines

The electrohydraulic control mechanisms of the ME engine replace the following components of the conventional MC engine: Chain drive for camshaft Camshaft with fuel cams, exhaust cams and indicator cams Fuel pump actuating gear, including roller guides and reversing mechanism Conventional fuel pressure booster and VIT system Exhaust valve actuating gear and roller guides Engine driven starting air distributor Electronic governor with actuator Regulating shaft Engine side control console Mechanical cylinder lubricators. The Engine Control System of the ME engine comprises: Control units Hydraulic power supply unit Hydraulic cylinder units, including: Electronically controlled fuel injection, and Electronically controlled exhaust valve activation Electronically controlled starting air valves Electronically controlled auxiliary blowers Integrated electronic governor functions Tacho system Electronically controlled Alpha lubricators

Main engine interlocks

Interlocks are provided so that the engine can be started or reversed only when certain conditions have been fulfilled. When there is a remote control of engines, it is essential to have interlocks. This reduces the possibility of engine damage and any hazards to the operating personnel. Turning gear Interlock . This device prevents the engine from being started if the Turning gear is engaged. Running Direction Interlock . This prevents the fuel from being supplied if the running direction of the engine does not match the Telegraph. Starting Air Distributor in end position . This prevents starting from taking place if the shifting of the Distributor has not been completed. Main Lube. oil pressure, Piston cooling pressure, Jacket water pressure, and important parameters must be above the required minimum. Auxiliary Blower Interlock . The Auxiliary Blower is provided in case of Constant pressure turbo charging. Air Spring pressure Interlock . In case of the present generation

Why is a man hole door elliptical in shape?

Any opening in a pressure vessel is kept to a minimum and for a man entry an elliptical hole  is lesser in size than the corresponding circular hole. More over it is prime concern to have a  smoothed generous radius at the corners to eliminate stress concentration. Hence other  geometrical shapes like rectangle and square are ruled out.  To compensate for the loss of material in the shell due to opening, a doubler ring has to be  provided around the opening. The thickness of the ring depends on the axis length along the  dirrection in which the stresses are maximum and the thickness of the shell. It is important to  align the minor axis along the length of the vessel, as the stress in this direction is  maximum. Longitudinal stress: Pd/2t where P= pressure inside the vessel, d= diameter of the arc, t=  thickness of the shell plating  Circumferential stress: Pd/4t  More over a considerable material and weight saving is achieved as minor is along the  direction of maximum stress.