Skip to main content

Emergency fire pump requirement: - SOLAS ch II-2 reg 10,

  1.   Independent driven power operated pump
  2.  Capacity should not be less than 40%  of the total fire pump capacity required by regulation II-2 / 10.2.2.4.hj1 and in any not less than 25 m3 /hr for cargo ships 200 Gt and above.
  3. (Each of the required fire pumps (other than any emergency pump required in paragraph 2.2.3.1.2 for cargo ships) shall have a capacity not less than 80% of the total required capacity divided by the minimum number of required fire pumps but in any case not less than 25 m3/h and each such pump shall in any event be capable of delivering at least the two required jets of water. These fire pumps shall be capable of supplying the fire main system under the required conditions. Where more pumps than the minimum of required pumps are installed such additional pumps shall have a capacity of at least 25 m3/h and shall be capable of delivering at least the two jets of water required in paragraph 2.1.5.1.)
  4. Minimum pressure at any hydrant  not less 2.7 bar.( 4.0 bar for passenger ship)
  5. Space containing should not be contiguous to the boundaries of machinery spaces or those spaces containing main fire pumps. Where this is not practicable, common bulkhead between the two spaces shall be insulated to a standard of structural fire protection equivalent to that required for control station.
  6. No direct access from engine room .( if impracticable then the access should be by air lock with door of machinery space being of A60 class standard and the other door being at least steel , both reasonably gas tight , self closing and without any hold back arrangement.
  7.  If diesel  driven , should be able to start by cranking at 0 deg. If impracticable , then there should be heating arrangement acceptable to admin. Starting at least 6 times within 30 min and at least twice within first 10 minutes.
  8. Fuel should be sufficient to run for 3 hrs and sufficient reserve fuel outside machinery space for 15 hrs running at full load.

Comments

  1. I would like to say this is a well-informed article as we have seen here.Intumescent Paint Applicator In Ksa Your way of writing is very impressive and also it is a beneficial article for us. Thanks for sharing an article like this.

    ReplyDelete
  2. I am glad that I came here and I can gain more information about this. You have written this article very factual which is understandable for everyone, Thanks for share it. Fire Smoke Detector

    ReplyDelete
  3. I am very grateful that I found some helpful content in this post. After reading it , I think that you have good knowledge. Thanks for posting it. Keep it up. Electrical Safety Supplier in Saudi Arabia

    ReplyDelete
  4. I am very thankful to you that you have shared this information with us. I got some different kind of knowledge from your web page, and it is really helpful for everyone. Thanks for share it. Read more info about Fireproof Paint on Metals Saudi Arabia

    ReplyDelete
  5. Your work is very good and I appreciate you and hopping for some more informative posts. Thank you for sharing great information to us. fire services design

    ReplyDelete
  6. Wow, this article is awesome wish to see more like this. Thanks for sharing such information. You can check this out too fire damage restoration sewell . Thank you.

    ReplyDelete
  7. Wow, this article is awesome wish to see more like this. Thanks for sharing such information. You can check this out too fire damage restoration sewell . Thank you.

    ReplyDelete
  8. Wow, this article is awesome wish to see more like this. Thanks for sharing such information. You can check this out too fire damage restoration sewell . Thank you.

    ReplyDelete
  9. Such beautifully written. And the information provided is very useful. Thanks for sharing such an informative and interesting article. Check this out too shredders industrial.Thanks!

    ReplyDelete
  10. You have published extraordinary article here about it. It is a genuinely beneficial info for us. Addressable fire alarms

    ReplyDelete

Post a Comment

If you have any doubts.Please let me know

Popular posts from this blog

Differences between MC/MC-C and ME/ME-C engines

The electrohydraulic control mechanisms of the ME engine replace the following components of the conventional MC engine: Chain drive for camshaft Camshaft with fuel cams, exhaust cams and indicator cams Fuel pump actuating gear, including roller guides and reversing mechanism Conventional fuel pressure booster and VIT system Exhaust valve actuating gear and roller guides Engine driven starting air distributor Electronic governor with actuator Regulating shaft Engine side control console Mechanical cylinder lubricators. The Engine Control System of the ME engine comprises: Control units Hydraulic power supply unit Hydraulic cylinder units, including: Electronically controlled fuel injection, and Electronically controlled exhaust valve activation Electronically controlled starting air valves Electronically controlled auxiliary blowers Integrated electronic governor functions Tacho system Electronically controlled Alpha lubricators

Main engine interlocks

Interlocks are provided so that the engine can be started or reversed only when certain conditions have been fulfilled. When there is a remote control of engines, it is essential to have interlocks. This reduces the possibility of engine damage and any hazards to the operating personnel. Turning gear Interlock . This device prevents the engine from being started if the Turning gear is engaged. Running Direction Interlock . This prevents the fuel from being supplied if the running direction of the engine does not match the Telegraph. Starting Air Distributor in end position . This prevents starting from taking place if the shifting of the Distributor has not been completed. Main Lube. oil pressure, Piston cooling pressure, Jacket water pressure, and important parameters must be above the required minimum. Auxiliary Blower Interlock . The Auxiliary Blower is provided in case of Constant pressure turbo charging. Air Spring pressure Interlock . In case of the present generation

Why is a man hole door elliptical in shape?

Any opening in a pressure vessel is kept to a minimum and for a man entry an elliptical hole  is lesser in size than the corresponding circular hole. More over it is prime concern to have a  smoothed generous radius at the corners to eliminate stress concentration. Hence other  geometrical shapes like rectangle and square are ruled out.  To compensate for the loss of material in the shell due to opening, a doubler ring has to be  provided around the opening. The thickness of the ring depends on the axis length along the  dirrection in which the stresses are maximum and the thickness of the shell. It is important to  align the minor axis along the length of the vessel, as the stress in this direction is  maximum. Longitudinal stress: Pd/2t where P= pressure inside the vessel, d= diameter of the arc, t=  thickness of the shell plating  Circumferential stress: Pd/4t  More over a considerable material and weight saving is achieved as minor is along the  direction of maximum stress.