Skip to main content

"Power" terminolagies used for Main Engine

Effective Power: The Power available at the output side of the engine i.e. at crankshaft flange of the engine which connects it with the flywheel and rest of the intermediate shaft

Rated Power: It is the continuous effective power provided by the manufacturer of the engine for a desired or rated RPM of the crankshaft. Rated power includes the loads which acts on the engine due to auxiliary system running from the engine power

Indicated Horse Power: It is a theoretical power calculated with a formula
                                          (PxLxAxN)  / 4500
                                            Where    P- Mean indicated pressure of the cylinder
                                                            L- Stroke of the engine
                                 .                         A-  Cross Sectional Area of the engine cylinder
    .                                                      N- Speed of the engine in RPM
                       .                                  4500 is a constant for conversion.
              In this calculation, the frictional losses are not considered. Since it is calculated from indicated pressure of  the engine, it is called Indicated Horse Power or IHP and used for calculating mechanical efficiency of the engine

Shaft Horse Power
: The power delivered by the engine to the propeller shaft is measured by an instrument known as torsion metre which is available on board.

Brake Horse Power
: This is the power measured at the crankshaft with the brake dynamometer and is always higher than the shaft horse power. This is because the power available at shaft accounts for frictional and mechanical losses.

Gross Power: Continuous effective power provided by the manufacturer for a given RPM using defined number of auxiliaries at normal service running condition without any overloading of the engine.

Continuous Power: It is the BHP measured at the power take off end when the engine is running at continuous safe operation range outside any time limit. This is provided by the supplier.

Overload Power: It is the power excess of effective power than the rated power for a short period of time, when the same auxiliaries are used under similar service condition for limited period.

Minimum Power: The guaranteed minimum or lower most power value by the manufacturer for an approximate crankshaft RPM is the minimum power of the engine.

Astern Output Power:
The maximum power engine can generate when running in the astern direction at safe condition.

Maximum Continuous Rating or MCR: It is the maximum power output engine can produce while running continuously at safe limits and conditions.

Standard Rating: This is the power output of the engine at normal service speed which gives the highest economical efficiency, thermal and mechanical efficiency. At this speed, the wear down of the engine is at the minimum rate

Comments

  1. Thanks for sharing the best information and suggestions, it is very nice and very useful to us. I appreciate the work that you have shared in this post. Keep sharing these types of articles here.Biometric Punching Mechine Solutions Dubai

    ReplyDelete
  2. This post is really awesome. Genuinely i like this blog. It gives me more useful information. I hope you share lots of things with us .Mitutoyo tools dealers in bangalore

    ReplyDelete

Post a Comment

If you have any doubts.Please let me know

Popular posts from this blog

Differences between MC/MC-C and ME/ME-C engines

The electrohydraulic control mechanisms of the ME engine replace the following components of the conventional MC engine: Chain drive for camshaft Camshaft with fuel cams, exhaust cams and indicator cams Fuel pump actuating gear, including roller guides and reversing mechanism Conventional fuel pressure booster and VIT system Exhaust valve actuating gear and roller guides Engine driven starting air distributor Electronic governor with actuator Regulating shaft Engine side control console Mechanical cylinder lubricators. The Engine Control System of the ME engine comprises: Control units Hydraulic power supply unit Hydraulic cylinder units, including: Electronically controlled fuel injection, and Electronically controlled exhaust valve activation Electronically controlled starting air valves Electronically controlled auxiliary blowers Integrated electronic governor functions Tacho system Electronically controlled Alpha lubricators

Main engine interlocks

Interlocks are provided so that the engine can be started or reversed only when certain conditions have been fulfilled. When there is a remote control of engines, it is essential to have interlocks. This reduces the possibility of engine damage and any hazards to the operating personnel. Turning gear Interlock . This device prevents the engine from being started if the Turning gear is engaged. Running Direction Interlock . This prevents the fuel from being supplied if the running direction of the engine does not match the Telegraph. Starting Air Distributor in end position . This prevents starting from taking place if the shifting of the Distributor has not been completed. Main Lube. oil pressure, Piston cooling pressure, Jacket water pressure, and important parameters must be above the required minimum. Auxiliary Blower Interlock . The Auxiliary Blower is provided in case of Constant pressure turbo charging. Air Spring pressure Interlock . In case of the present generation

Why is a man hole door elliptical in shape?

Any opening in a pressure vessel is kept to a minimum and for a man entry an elliptical hole  is lesser in size than the corresponding circular hole. More over it is prime concern to have a  smoothed generous radius at the corners to eliminate stress concentration. Hence other  geometrical shapes like rectangle and square are ruled out.  To compensate for the loss of material in the shell due to opening, a doubler ring has to be  provided around the opening. The thickness of the ring depends on the axis length along the  dirrection in which the stresses are maximum and the thickness of the shell. It is important to  align the minor axis along the length of the vessel, as the stress in this direction is  maximum. Longitudinal stress: Pd/2t where P= pressure inside the vessel, d= diameter of the arc, t=  thickness of the shell plating  Circumferential stress: Pd/4t  More over a considerable material and weight saving is achieved as minor is along the  direction of maximum stress.