Skip to main content

Securing propellers

HYDRAULIC FLOATING OF PROPELLERS

Used for keyless propellers, ensures the correct interference fit using measured oil pressures for expanding the boss and hydraulic jacks or a Pilgrim nut for pushing it up or down the tailshaft taper. No heavy slogging required and low shock loads are applied, quick and safe.
A disadvantage is loss of bearing area due to oil grooves which means that propeller must be longer or greater in Dia to give sufficient area to transmit the torque.
To remove, nut just slackened back. Oil injection applied to expand the boss which allows propeller to move off the taper.
Another disadvantage of wet fitting over dry fitting is that wet boss expansion stress is 30% greater than dry fitted which means that boss must be thicker.






SLEEVED PROPELLER

 Usually fitted on large diameter shafting. Usually hydraulically floated and keyless. Difficult to bed large props to taper, easier to bed sleeve. Also each time a prop is refitted, prop bore becomes larger, this is accentuated in large bore dia props. Hence, after a few refits the prop moves to far up the shaft, more economical to replace the sleeve than the whole prop.
Pearlitic cast iron used to mate with forged mild steel shaft because this combination offers the greatest resistance to fretting which can be caused by prop excited vibration

Molecular fretting can occur internally, generally from the center outward due to molecular rubbing together. Surface fretting occurs at the surface due to two items moving over each other due to vibration.When fitting or removing, heat not to be used since it may effect the mechanical properties of the resin. Wedging or withdrawal systems should not be used since this would cause shearing of the araldite.

TRADITIONAL METHOD

Shaft turned to top centre, i.e. when key is on top, convenient for key way inspection and prop slinging. Shaft locked, and prop nut just slacked.
Coupling bolts at tail end flange removed, if lignum vitae bearing- stuffing bearing removed and tailed flange shored up against aft peak bulkhead.
Secured lifting gear to propeller, then wedge off prop using box wedges between stern tube nut and ford face of prop.
If tail end and bronze liner are to be inspected then it must be brought inboard which requires the removal of one or two lengths of intermediate shafting.






BOLTED

Controllable pitch propellers require a hollow prop shaft for the oil and feed back tubes to pass through. non of the above methods are suited to this.
Instead the propeller is bolted to a flange, the other end of the propshaft must therefore be parallel to allow removal from the stern bearing.
The prop shaft is attached to the intermediate shaft by a 'muff' coupling. Once the bolts have been tightened they are secured by tack welding locking bars across the heads.

Comments

  1. You've written a very useful article. This article provided me with some useful knowledge. Thank you for providing this information. Keep up the good work. DOUBLE SLEEVED

    ReplyDelete

Post a Comment

If you have any doubts.Please let me know

Popular posts from this blog

Differences between MC/MC-C and ME/ME-C engines

The electrohydraulic control mechanisms of the ME engine replace the following components of the conventional MC engine: Chain drive for camshaft Camshaft with fuel cams, exhaust cams and indicator cams Fuel pump actuating gear, including roller guides and reversing mechanism Conventional fuel pressure booster and VIT system Exhaust valve actuating gear and roller guides Engine driven starting air distributor Electronic governor with actuator Regulating shaft Engine side control console Mechanical cylinder lubricators. The Engine Control System of the ME engine comprises: Control units Hydraulic power supply unit Hydraulic cylinder units, including: Electronically controlled fuel injection, and Electronically controlled exhaust valve activation Electronically controlled starting air valves Electronically controlled auxiliary blowers Integrated electronic governor functions Tacho system Electronically controlled Alpha lubricators

Main engine interlocks

Interlocks are provided so that the engine can be started or reversed only when certain conditions have been fulfilled. When there is a remote control of engines, it is essential to have interlocks. This reduces the possibility of engine damage and any hazards to the operating personnel. Turning gear Interlock . This device prevents the engine from being started if the Turning gear is engaged. Running Direction Interlock . This prevents the fuel from being supplied if the running direction of the engine does not match the Telegraph. Starting Air Distributor in end position . This prevents starting from taking place if the shifting of the Distributor has not been completed. Main Lube. oil pressure, Piston cooling pressure, Jacket water pressure, and important parameters must be above the required minimum. Auxiliary Blower Interlock . The Auxiliary Blower is provided in case of Constant pressure turbo charging. Air Spring pressure Interlock . In case of the present generation

Why is a man hole door elliptical in shape?

Any opening in a pressure vessel is kept to a minimum and for a man entry an elliptical hole  is lesser in size than the corresponding circular hole. More over it is prime concern to have a  smoothed generous radius at the corners to eliminate stress concentration. Hence other  geometrical shapes like rectangle and square are ruled out.  To compensate for the loss of material in the shell due to opening, a doubler ring has to be  provided around the opening. The thickness of the ring depends on the axis length along the  dirrection in which the stresses are maximum and the thickness of the shell. It is important to  align the minor axis along the length of the vessel, as the stress in this direction is  maximum. Longitudinal stress: Pd/2t where P= pressure inside the vessel, d= diameter of the arc, t=  thickness of the shell plating  Circumferential stress: Pd/4t  More over a considerable material and weight saving is achieved as minor is along the  direction of maximum stress.