Skip to main content

Overheating of Main Engine Piston

Reasons: 
  • Inadequate circulation of cooling media and or supply not sufficient
  • Excessive deposit in cooling space (scale or carbon)
  • Lubrication not sufficient
  • Faulty piston ring : clearance inadequate. 
  • Too high temperature 
  • top ring groove area – blow by.
  • Distorted cylinder liner
  • Misalignment of piston
  • Overloading of unit – excessive fuel
  • Excessive water content in fuel
  • Insufficient air from turbocharger or manifold
  • Late injection of fuel – timing or fault injectors
  • Engine running slow speed – full flow of coolant not maintained
Action:
  • Slow down the engine to a very low speed but NOT complete shutdown. This results in considerable reduction of heat in the relevant piston.
  • Since not all pistons would likely develop this fault simultaneously (unless you are totally out of luck that day) so first identify the particular cylinder in which the problem has occurred using parameters such as temperatures, sound etc.
  • The fuel supply to the affected cylinder should be cut-down from the fuel pump
  • Lubrication to that cylinder should be increased from the appropriate arrangement depending on the specific engine under consideration
  • Only stop the engine when it is sufficiently cooled to avoid any thermal stresses. Even after stopping the turning gear should be used to keep it moving for some time while cooling and lubrication is continued.
  • Finally the piston needs to be dismantled and checked and this is a detailed procedure which we might take up in future

Labels:

Comments

Post a Comment

If you have any doubts.Please let me know

Popular posts from this blog

Differences between MC/MC-C and ME/ME-C engines

The electrohydraulic control mechanisms of the ME engine replace the following components of the conventional MC engine: Chain drive for camshaft Camshaft with fuel cams, exhaust cams and indicator cams Fuel pump actuating gear, including roller guides and reversing mechanism Conventional fuel pressure booster and VIT system Exhaust valve actuating gear and roller guides Engine driven starting air distributor Electronic governor with actuator Regulating shaft Engine side control console Mechanical cylinder lubricators. The Engine Control System of the ME engine comprises: Control units Hydraulic power supply unit Hydraulic cylinder units, including: Electronically controlled fuel injection, and Electronically controlled exhaust valve activation Electronically controlled starting air valves Electronically controlled auxiliary blowers Integrated electronic governor functions Tacho system Electronically controlled Alpha lubricators
9 comments
Read more

Main engine interlocks

Interlocks are provided so that the engine can be started or reversed only when certain conditions have been fulfilled. When there is a remote control of engines, it is essential to have interlocks. This reduces the possibility of engine damage and any hazards to the operating personnel. Turning gear Interlock . This device prevents the engine from being started if the Turning gear is engaged. Running Direction Interlock . This prevents the fuel from being supplied if the running direction of the engine does not match the Telegraph. Starting Air Distributor in end position . This prevents starting from taking place if the shifting of the Distributor has not been completed. Main Lube. oil pressure, Piston cooling pressure, Jacket water pressure, and important parameters must be above the required minimum. Auxiliary Blower Interlock . The Auxiliary Blower is provided in case of Constant pressure turbo charging. Air Spring pressure Interlock . In case of the present generation
7 comments
Read more

Why is a man hole door elliptical in shape?

Any opening in a pressure vessel is kept to a minimum and for a man entry an elliptical hole  is lesser in size than the corresponding circular hole. More over it is prime concern to have a  smoothed generous radius at the corners to eliminate stress concentration. Hence other  geometrical shapes like rectangle and square are ruled out.  To compensate for the loss of material in the shell due to opening, a doubler ring has to be  provided around the opening. The thickness of the ring depends on the axis length along the  dirrection in which the stresses are maximum and the thickness of the shell. It is important to  align the minor axis along the length of the vessel, as the stress in this direction is  maximum. Longitudinal stress: Pd/2t where P= pressure inside the vessel, d= diameter of the arc, t=  thickness of the shell plating  Circumferential stress: Pd/4t  More over a considerable material and weight saving is achieved as minor is along the  direction of maximum stress.
20 comments
Read more