Skip to main content

TriboPack

The design measures incorporated in TriboPack are:
  • Multi-level cylinder lubrication
  • Liner of the appropriate material, with sufficient hard phase
  • Careful turning of the liner running surface and deep-honing of the liner over the full length of the running surface
  • Mid-stroke liner insulation, and where necessary, insulating tubes in the cooling bores in the upper part of the liner
  • Pre-profiled piston rings in all piston grooves
  • Chromium-ceramic coating on top piston ring
  • RC (Running-in Coating) piston rings in all lower piston grooves
  • Anti-Polishing Ring (APR) at the top of the cylinder liner
  • Increased thickness of chromium layer in the piston-ring grooves.

Labels:

Comments

  1. NTX InsulationApril 29, 2021 at 8:22 AM

    Thank you so much for sharing this blog with us. It provides a collection of useful information. You obviously put a lot of effort into it! Best Foam Insulation Frisco Texas service provider.

    ReplyDelete
  2. American Insulation CoDecember 4, 2021 at 10:15 AM

    I read this article, it is really informative one. Your way of writing and making things clear is very impressive. Thanking you for such an informative article.Attic Insulation near Me

    ReplyDelete

Post a Comment

If you have any doubts.Please let me know

Popular posts from this blog

Main engine interlocks

Interlocks are provided so that the engine can be started or reversed only when certain conditions have been fulfilled. When there is a remote control of engines, it is essential to have interlocks. This reduces the possibility of engine damage and any hazards to the operating personnel. Turning gear Interlock . This device prevents the engine from being started if the Turning gear is engaged. Running Direction Interlock . This prevents the fuel from being supplied if the running direction of the engine does not match the Telegraph. Starting Air Distributor in end position . This prevents starting from taking place if the shifting of the Distributor has not been completed. Main Lube. oil pressure, Piston cooling pressure, Jacket water pressure, and important parameters must be above the required minimum. Auxiliary Blower Interlock . The Auxiliary Blower is provided in case of Constant pressure turbo charging. Air Spring pressure Interlock . In case of the present generation...
7 comments
Read more

Differences between MC/MC-C and ME/ME-C engines

The electrohydraulic control mechanisms of the ME engine replace the following components of the conventional MC engine: Chain drive for camshaft Camshaft with fuel cams, exhaust cams and indicator cams Fuel pump actuating gear, including roller guides and reversing mechanism Conventional fuel pressure booster and VIT system Exhaust valve actuating gear and roller guides Engine driven starting air distributor Electronic governor with actuator Regulating shaft Engine side control console Mechanical cylinder lubricators. The Engine Control System of the ME engine comprises: Control units Hydraulic power supply unit Hydraulic cylinder units, including: Electronically controlled fuel injection, and Electronically controlled exhaust valve activation Electronically controlled starting air valves Electronically controlled auxiliary blowers Integrated electronic governor functions Tacho system Electronically controlled Alpha lubricators
14 comments
Read more

Shell Expansion Plan

It is a two dimensional drawing of a three dimensional surface of the ship’s hull form. This plan is very useful for the following information:It is used for marking the location of a hull Damage on this plan by identifying the strake number , letter and frame number so that the exact location of the damage and also suggested repairs are marked in a localised copy. The shell expansion can be used for finding areas of painting surfaces such as topside, boot topping and bottom areas by applying Simpsons rules directly.  In the shell expansion the vertical scale used is different from the horizontal scale and a suitable adjustment has to be made when calculating areas. This becomes useful in solving disputes concerning areas of preparation and painting. It gives information on the thickness of the original strake which is indicated by the number in the circle shown in the strake.  The quality of steel used is also shown by letters A,B,D E and AH, BH,DH, EH.
20 comments
Read more