Skip to main content

Handling Electro-mechanical Governor of Marine Engine

 

The speed of the marine engine is controlled by an instrument known as governor, which can be of – hydraulic, electro-hydraulic or electronic governor type.


The most famous types of governor used for both main engine and generator engine is the electro-hydraulic type marine governor. It’s because of this little instrument that the engine speed can be smoothly controlled from a remote space (bridge or engine control room).

The different components of a governor allows for a steady state speed control, along with achieving the required variation in the load.

Following are the important parts of the governor:

– Synchronizer knob: This knob is used for controlling the speed of the engine with a single unit (Main engine) and controlling the load for engines with multiple unit (generator)

– Speed droop knob: The speed droop knob helps in creating the stability and also divides the load equally among multiple generator engines running parallel

– Load limit knob: This knob controls and limits the load on the engine by restricting the travel of the governor shaft, which is connected to the fuel shaft of the engine

– Synchronizer indication knob: This knob does not have any control function and it is used to show how many turns the synchronizer knob has rotated

When handling the electro-hydraulic governor of a marine engine, following things to be kept in mind:

1. Ensure the governor travel/ output shaft connected to the fuel shaft is provided with sufficient over-travel at each end of the terminal shaft. Failing to do so will either prevent it from giving more fuel at maximum fuel position or will shut down the prime mover when the shaft is in minimum fuel position

2. Ensure the oil level and quality is correctly maintained. The viscosity of the oil inside the governor at normal operating temperature should be in the range of 20 cst to 65cst. The recommended continuous operating temperature of the governor oil is 60 Deg C to 93 deg C.

3. Never manually force the prime mover fuel linkage to increase the fuel without the first turning the load limit knob to maximum position of “10” else it will damage the governor’s internal parts

4. Ensure to apply as little compensation (through compensation needle provided for controlling the speed/load variation) as possible as higher compensation setting will lead to more fluctuation in speed with load change

5. For generator system running in parallel, set the speed droop at sufficiently high setting to avoid interchange of load between units while running

6. Synchronizer knob can be used to adjust the system frequency and to distribute the load between the units

7. Ensure to keep a check on the synchromotor for insulation and proper operation provided on the top of the governor, which transfers the remote signal to the governor for increasing or decreasing the engine speed

8. Ensure to check the tightness of the foundation bolts of the governor along with the tightness of the cable for synchro-motor. The governor is a high speed rotating instrument and excessive vibration with loose foundation will damage the interior parts

9. While testing the governor after overhauling, ensure all linkages are proper and oil level is upto the mark. Hold the output shaft with a serration wrench (monkey spanner) to manually control the speed in case the governor malfunctions

10. Never attempt to adjust the settings or the internal parts of the governor until you are thoroughly familiar with the proper procedure

It is very important that ship engineers are familiar with the planned maintenance of the governor. In no circumstances an engine with faulty governor should be operated as it may result in over-speeding of the engine and fatal accidents.

Over to you..

Comments

Post a Comment

If you have any doubts.Please let me know

Popular posts from this blog

Main engine interlocks

Interlocks are provided so that the engine can be started or reversed only when certain conditions have been fulfilled. When there is a remote control of engines, it is essential to have interlocks. This reduces the possibility of engine damage and any hazards to the operating personnel. Turning gear Interlock . This device prevents the engine from being started if the Turning gear is engaged. Running Direction Interlock . This prevents the fuel from being supplied if the running direction of the engine does not match the Telegraph. Starting Air Distributor in end position . This prevents starting from taking place if the shifting of the Distributor has not been completed. Main Lube. oil pressure, Piston cooling pressure, Jacket water pressure, and important parameters must be above the required minimum. Auxiliary Blower Interlock . The Auxiliary Blower is provided in case of Constant pressure turbo charging. Air Spring pressure Interlock . In case of the present generation...
7 comments
Read more

Differences between MC/MC-C and ME/ME-C engines

The electrohydraulic control mechanisms of the ME engine replace the following components of the conventional MC engine: Chain drive for camshaft Camshaft with fuel cams, exhaust cams and indicator cams Fuel pump actuating gear, including roller guides and reversing mechanism Conventional fuel pressure booster and VIT system Exhaust valve actuating gear and roller guides Engine driven starting air distributor Electronic governor with actuator Regulating shaft Engine side control console Mechanical cylinder lubricators. The Engine Control System of the ME engine comprises: Control units Hydraulic power supply unit Hydraulic cylinder units, including: Electronically controlled fuel injection, and Electronically controlled exhaust valve activation Electronically controlled starting air valves Electronically controlled auxiliary blowers Integrated electronic governor functions Tacho system Electronically controlled Alpha lubricators
9 comments
Read more

Why is a man hole door elliptical in shape?

Any opening in a pressure vessel is kept to a minimum and for a man entry an elliptical hole  is lesser in size than the corresponding circular hole. More over it is prime concern to have a  smoothed generous radius at the corners to eliminate stress concentration. Hence other  geometrical shapes like rectangle and square are ruled out.  To compensate for the loss of material in the shell due to opening, a doubler ring has to be  provided around the opening. The thickness of the ring depends on the axis length along the  dirrection in which the stresses are maximum and the thickness of the shell. It is important to  align the minor axis along the length of the vessel, as the stress in this direction is  maximum. Longitudinal stress: Pd/2t where P= pressure inside the vessel, d= diameter of the arc, t=  thickness of the shell plating  Circumferential stress: Pd/4t  More over a considerable material and weight saving is achieved as...
20 comments
Read more